Natural and enriched Cr target development for production of Manganese

Scientific Reports volume 13, Article number: 1167 (2023) Cite this article

499 Accesses

1 Altmetric

Metrics details

52Mn is a promising PET radiometal with a half-life of 5.6 days and an average positron energy of 242 keV. Typically, chromium of natural isotope abundance is used as a target material to produce this isotope through the nat/52Cr(p,n)52Mn reaction. While natural Cr is a suitable target material, higher purity 52Mn could be produced by transitioning to enriched 52Cr targets to prevent the co-production of long-lived 54Mn (t1/2 = 312 day). Unfortunately, 52Cr targets are not cost-effective without recycling processes in place, therefore, this work aims to explore routes to prepare Cr targets that could be recycled. Natural Cr foils, metal powder pellets, enriched chromium-52 oxide and Cr(III) electroplated targets were investigated in this work. Each of these cyclotron targets were irradiated, and the produced 52Mn was purified, when possible, using a semi-automated system. An improved purification by solid-phase anion exchange from ethanol-HCl mixtures resulted in recoveries of 94.5 ± 2.2% of 52Mn. The most promising target configuration to produce a recyclable target was electroplated Cr(III). This work presents several pathways to optimize enriched Cr targets for the production of high purity 52Mn.

Manganese-52 (52Mn) is a positron emitting radiometal which can be used for long-lived studies using positron emission tomography (PET). Additionally, since non-radioactive Mn has previously been used as a contrast enhancing agent for Manganese Enhanced MRI (MEMRI), radioactive 52Mn can be combined with the nonradioactive Mn to create a dual modality signal enhancing contrast agent for imaging with PET/MRI1.

One of the most common routes of production for 52Mn is nat/52Cr(p,n)52Mn. Several researchers have reported on the preparation and characterization of Cr targets of natural isotopic abundance (natural Cr). (Table 1). Other methods have used Vanadium targets to make 52Mn via bombardment with 3He, however, there are only a limited number of accelerators that have the capabilities to accelerate these particles2.

Natural Cr consists of 4 isotopes of Cr including 50Cr (4.35%), 52Cr (83.79%), 53Cr (9.50%), and 54Cr (2.37%). Since natural Cr contains a high percentage of 52Cr, it is an inexpensive route to produce 52Mn. Unfortunately, the reactions that occur on the other three stable isotopes of Cr can lead to the production of several radiocontaminants via this irradiated target material as shown in Table 2. If the cross sections and thresholds of these reactions are taken into consideration and the proton beam energy is kept below ~ 13 MeV, only two of these impurities, 52mMn and 54Mn, are observed in the gamma spectra after irradiation of the natural chromium1,9,10,11. Previous studies have optimized the bombardment parameters through cross section measurements10. Another solution to prevent the production of these long lived impurities would be to use an enriched 52Cr target.

Therefore, we aimed to develop enriched 52Cr targets using chemistry which would enable recycling of the target material to make new targets at a reduced cost. Natural Cr targets were used to carry out feasibility studies for production, purification, and recycling processes before the transition to 52Cr. Cr can be purchased in many different forms including powder, foils, rods, however, 52Cr is typically obtained in metal powder form. Cr powders can be pressed into powder targets using a hydraulic press, reacted to produce other chemical forms, such as, Cr2O3 or CrCl3, or electroplated to increase the potential for recyclable enriched 52Cr targets. Since Cr(VI) is considered to have higher toxicity this work avoided that oxidation state and focused on the less toxic Cr(III). This work examined various species and target configurations of Cr to explore recyclable enriched 52Cr targets.

Natural Cr metal powder with 5N purity, Ta sheets with 3N8 purity, Al sheets with 5N purity, Cu sheets with 5N5 purity, Au sheets with 5N purity and Pt rods with 3N5 purity were obtained from ESPI Metals, Ashland, OR. Enriched 52Cr metal powder with 98.8% enrichment was obtained from Isoflex, San Francisco, CA. Viton O-rings were obtained from McMaster-Carr, Elmhurst, IL. The 10 mm diameter ID dry pressing die set was obtained from Across International (Livingston, NJ). Chromium chloride hexahydrate with purity ≥ 98% and 1 mL SPE tubes with frits were obtained from Millipore Sigma, Burlington, MA. AG1-X8 resin analytical grade 100–200 mesh chloride form was obtained from Bio-Rad, Hercules, CA. A mixed nuclide source in a sealed 1.5 mL centrifuge tube used for high purity germanium detector (HPGe) calibration was prepared by Eckert & Ziegler Analytics (Atlanta, GA). 1,4,7,10-tetraazacyclododecane-1,4,7,10-tetraacetic acid (DOTA) was obtained from Macrocyclics (Plano, TX) and the Aluminum backed Si-60 TLC plates were obtained from Sorbtech technologies (Norcross, GA).

All other materials were purchased from Fisher Scientific (Hampton, NH) unless stated otherwise.

As reported in Pyles et al. 2021, Cr foils were produced on a large scale by electrodeposition of natural abundance Cr as previously described in Wooten et al. 201511,13.

Cr metal powder targets were made by pressing 200–230 mg of natural Cr metal powder at 5 tons for 5 min using a hydraulic press and 10 mm dye set. These targets were 10 mm in diameter and had 0.4–0.5 mm nominal thickness. Tantalum (Ta) sheets with 3N8 purity and thickness of 0.06 in, were cut into a 2.5 cm diameter coins and a 0.5 mm deep divot was machined into the center to hold the Cr powder target. Additionally, these targets had a divot for a Viton O-ring outside of the target divot as to prevent the loss of target material. The targets were finally capped with a 0.75 mm Aluminum (Al) degrader with a “push button” design to fit into the 14 mm divot to cover both the target and the O-ring as shown in Fig. 1A.

Photos of target configurations described before irradiation. (A) Cr metal powder target with Al “push button” degrader, (B) Cr2O3 target, (C) electroplated Cr(III) target.

52Cr2O3 was made by the reactions.

Using enriched 52Cr metal powder as a starting material.

200–230 mg of 52Cr was dissolved in 5 mL of 6 M hydrochloric acid (HCl) heated to 95 °C for approximately 30 min or until dissolved to yield 52CrCl3. Approximately 10 mL of 7 M ammonium hydroxide was added to the 52CrCl3 solution to precipitate the material as 52Cr(OH)3. The 52Cr(OH)3 was then centrifuged at 3000 rpm for 7 min or until the precipitate was separated from the solution. The precipitate pellet was separated from the supernatant, and rinsed with MQ water. The 52Cr(OH)3 was heated at 200–250 °C to obtain the final product of 52Cr2O3. Then the 52Cr2O3 powder was weighed and placed in the oven to keep it dry at 250 °C. The powder targets were made by pressing 200–230 mg of 52Cr2O3 powder in a 10 mm diameter ID dry pressing die set, to ensure the correct target shape, at 5 tons for 5 min using a hydraulic press to make the pressed pellet used for irradiations. These targets were 10 mm in diameter and had 0.4–0.5 mm nominal thickness. The target was configured as described in Section 1.3 with the Ta backing and Al “push button” degrader as shown in Fig. 1B.

Chromium chloride hexahydrate (CrCl3·6H2O) was utilized as the chromium source in the electrodeposition solution which was adapted from the procedure previously described in Liang et al.14. A 20 × 150 mm lime glass disposable culture tube modified to have two open ends was used as the electrolysis cell. The plating diameter was 10 mm with a 0.1–0.5 mm nominal thickness depending on the amount of Cr plated as shown in Fig. 1C. Copper (Cu) or Gold (Au) sheets with 5N5 and 5N purity, respectively, and thickness of 0.75 mm were cut into a 2.5 cm diameter coins to be used as the target backing (cathode) while a platinum rod was used as the rotating anode suspended in the solution. The electroplating apparatus was connected to a DC power supply that utilized alligator clips in order to apply voltage to the platinum rod. (Fig. 2) The voltage applied to the platinum rod and the electroplating solution was 3.8 V which supplied a current averaging 0.075 A. Additionally, these targets were finally capped with a 0.75 mm Al degrader.

Electroplating apparatus used to plate Cr metal from a CrCl3 solution where the cathode is located between the base plate and the plastic coin holder. The anode is the platinum rod which can be seen connected to the motor and suspended in the CrCl3 plating solution.

The stopping and range of ions in matter (SRIM) was used to determine the energy of the proton beam on target after the degrader15. All bombardments were performed on the TR-24 Cyclotron (Advanced Cyclotron Systems Inc). The irradiations below used bombardment parameters previously optimized by El Sayed et al. These target configurations were irradiated with an incident proton beam energy of 17.5 MeV on the degrader (12.8 MeV on the Cr target material) at 15 μA for 2–8 h. The proton beam was stopped in the backing coin described in each target configuration. The target was cooled by He gas on the front of the target while the back of the target was water cooled.

The electroplated targets were analyzed by the SEM to determine the purity of the plated Cr. SEM analysis was performed with a SEM FEI Quanta 650 FEG with secondary electron detector at an acceleration voltage of 16 kV for spectroscopy equipped with an electron dispersive X-ray spectroscopy (EDAX) analyzer to measure qualitatively the sample stoichiometry. The SEM utilized the xT microscope control software while the EDAX used Teams software.

The purification method described below was adapted from Pyles et al. except for the natural Cr foils which used the exact separation process written in Pyles et al.13. For the adapted studies, three columns composed of 1 mL solid-phase extraction (SPE) tubes were loaded with AG1-X8 resin as follows: column 1 (C1)—300 mg, column 2 (C2)—200 mg and column 3 (C3)—100 mg. A frit provided with the SPE tubes was added on top of the AG1-X8 resin to prevent the resin bed from being disturbed by the incoming reagents during the purification process. The irradiated Cr target was dissolved in concentrated HCl, diluted to 3% HCl in EtOH and loaded onto a column containing AG1-X8 resin. The Cr was eluted with 3% HCl in ethanol. The Mn was eluted with 6 M HCl.

The adapted procedure of the three-column chemistry separation is described in Table 3 and Fig. 3.

Adapted schematic of semi-automated system designed to separate 52Mn from the chromium target material, valve control and syringe pumps while syringes 1–6 are operated manually. B1-3: Beaker 1–3; T1-3: 50 mL conical vial 1–3; C1-3: Column 1–3; V1-5: Valve 1–5; ABCD: 4-way valve; S1-6: Syringe 1–6; SP1-2: Syringe pump 1–2; FPV: Final product vial. Modified from Pyles et al.13.

After irradiation and target dissolution, aliquots were collected from the crude solution of dissolved natCr and 52Cr targets before and after purification. Samples were analyzed as described in Pyles et al.13.

Inductively Coupled Plasma-Mass Spectroscopy (ICP-MS, 7700 Series; Agilent, Santa Clara, CA) was used to evaluate the presence of Cr in the dissolved target material and the solutions eluted from each column. Aliquots of each sample were taken and analyzed as described in Pyles et al.13.

To assess the chemical purity and apparent molar activity (AMA) of the 52Mn produced by the natural chromium metal powder targets, a chelation assay was carried out as previously described by Graves et al.4. Briefly 52MnCl2 was dried down and reconstituted in 0.1 M ammonium acetate, pH 4.5. A twofold serially diluted samples of DOTA (1,4,7,10-tetraazacyclododecane-1,4,7,10-tetraacetic acid) 1 mg/mL in 0.1 M ammonium acetate, pH 4.5 were prepared. 100 μL of buffered activity was combined with each of the DOTA samples and incubated at 37 °C for 1 h. The labeling efficiency of the samples was assessed by spotting 2 μL of each sample on Aluminum backed Si-60 TLC plates. The plates were developed in 0.1 M HCl mobile phase, 52Mn-DOTA remained at the origin and free 52Mn moved with the mobile phase.

The details of each target configuration’s irradiation and purification results are listed in Table 4. The theoretical values for each target were calculated using the thick target yield measurement and are in agreement with the experimental yields.

In the original target configuration of 1–2 natural Cr foil(s) and purification method previously described in Pyles et al., the foils are no longer available and two–three columns were used13. The amounts of Cr and nonradioactive Mn in the final product per batch [batch size: 284.9 ± 48.1 MBq (7.7 ± 1.3 µCi)] for the radioactive purifications were 5.6 ± 8.6 μg and 1.3 ± 2.3 μg, respectively. The iron and copper contaminants for the radioactive purifications per batch were 79 ± 14 µg (1.41 µmol) and 54 ± 2 µg (0.85 µmol), respectively.

This target configuration was determined to be the most successful in terms of ease of overall use. High yields of 336.7 ± 44.4 MBq (9.1 ± 1.2 mCi) were obtained after an 8 h irradiation. These targets were simple to assemble and purify with high percent recoveries of 52Mn at 93.1 ± 2.5%. The purification system separated Mn from the Cr target material by using a series of three 1 mL SPE tubes. The target purification for of natural chromium powder [batch size: 336.7 ± 44.4 MBq (9.1 ± 1.2 µCi)] resulted in ICP-MS data for Cr (10.5 ± 2.6 µg), Mn (2.0 ± 0.6 µg), Fe (7.2 ± 1.3 µg), Cu (2.9 ± 0.4 µg) and Zn (13.2 ± 1.0 µg) for each of the final products. One downfall is this target cannot be recycled and therefore was not deemed a good candidate to be converted to an enriched 52Cr target unless recycling was not necessary.

Then the 52Cr2O3 powder was weighed and 411.5 ± 44.5 mg was placed in the oven to keep it dry at 250 °C. These target configurations were very similar to the natural chromium metal powder, however, the enriched 52Cr metal was used to make the 52Cr2O3. The enriched material resulted in higher yields in a shorter time of 318.2 ± 7.4 MBq (8.6 ± 0.2 mCi) in 2.5 h. Unfortunately, this material did not dissolve in any of the following acids and bases in their concentrated forms: hydrochloric acid, nitric acid, sulfuric acid, hydrofluoric acid, and sodium hydroxide. Mixtures of these acids were also attempted without success using aqua regia and piranha solution. This is in line with prior literature reports that harsh conditions are required to dissolve Cr2O3, therefore, this target could not be purified to obtain the purified 52Mn16,17. If a reasonable dissolution was developed these targets could be recycled and reused for an enriched 52Cr target. The recycling process would utilize the reaction listed to make the 52Cr2O3 starting with the CrCl3 that is collected during the purification process.

The electroplated Cr utilizes chromium oxide hexahydrate in the electrodeposition solution. The formic acid and urea were used as complexing agents while the ammonium chloride and sodium chloride were used as conducting salts and finally the methanol and boric acid were used as buffering agents. These targets were further investigated by a scanning electron microscope (SEM) (Fig. 4). The analytical technique confirmed that the electroplated targets contained 95.6 ± 1.0% by weight percent and 89.3 ± 1.1% by atomic percent of Cr on the surface with 3.2 ± 0.2% by weight percent and 9.7 ± 0.6% by atomic percent of oxygen using a Cu backing. The electroplated targets using an Au backing contained 93.5 ± 1.5% by weight percent and 83.1 ± 3.9% by atomic percent of Cr on the surface with 5.6 ± 1.2% by weight percent and 16.5 ± 3.1% by atomic percent of oxygen before sanding the surface and contained 93.7 ± 0.6% by weight percent and 82.0 ± 1.4% by atomic percent of Cr on the surface with 6.3 ± 0.6% by weight percent and 18.0 ± 1.4% by atomic percent of oxygen after sanding the surface. While the amount of Cr is slightly increased on the Cu backing, the Au is more practical as elevated Cu in the final product was observed when the Cu backings were used due to slight dissolution of Cu during the dissolution of the Cr target material. Plating yields were 16.8 ± 2.6% which could be improved for conversion to an enriched recycled target.

Scanning electron microscope (SEM) image and the energy dispersive X-ray analysis (EDAX) spectra for a representative electroplated Cr(III) target with a (A) Cu backing, (B) Au backing (C) Au backing after sanding.

The purification system separated Mn from the Cr target material by using a series of three 1 mL SPE tubes. The results from the radioactive purifications were obtained using the electroplated Cr(III) targets shown in Fig. 5. The target purifications for electroplated Cr(III) targets [batch size: 118.4 ± 7.4 MBq (3.2 ± 0.2 µCi)] resulted in ICP-MS data for Cr (1.0 ± 0.5 µg), Mn (0.6 ± 0.03 µg), Fe (4.9 ± 1.6 µg), Cu (4.5 ± 0.3 µg) and Zn (14.3 ± 2.3 µg) for each final product. Additionally, the improved purification process increased the percent yield of 52Mn from 70.8 ± 3.3% (n = 3) (Pyles et al.) to 94.5 ± 2.2% when both the electroplated and chromium metal powder targets are considered.

ICP-MS and HPGe data of radioactive purifications of 52Mn using the three-column semi-automated system. The results are expressed in Average ± SD; N = 3. SM Starting Material, C1 Column 1, C2 Column 2, C3 Column 3, W Waste material.

The radionuclidic purity of the samples was verified via gamma-ray spectroscopy where samples were acquired before, during and after purification of 52Mn. 52mMn (a meta-stable state of 52Mn with a t1/2 = 21.1 min) and 50Mn were not present in the spectra due to their short half-lives. 51Cr was not present in the spectra where the limit of detection was less than 1.24 ± 0.32%. The amount of 54Mn detected in the final sample was 0.125 ± 0.124% of the total sample displayed in the top gamma spectra of Fig. 6. When an enriched 52Cr target was used the 54Mn was less than the limit of detection of 0.01 ± 0.001% displayed in the bottom gamma spectra of Fig. 6.

Top. Representative gamma spectra taken after the 52Mn purification process of the natural Cr metal powder target (all natural targets discussed showed similar spectra with the same peaks) showing a lack of 51Cr peak (320.1 keV). However, the 54Mn peak (835.85 keV), highlighted in red, can still be observed as well as the many characteristic peaks of 52Mn (345.8, 744.23, 847.7, 935.54, 1246.28, and 1333.65 keV) when natural Cr targets are used. Bottom. Representative gamma spectra taken after the 52Mn purification process showing the absence of the 54Mn peak when the enriched 52Cr metal powder target was used1,13.

Varying labeling efficiencies of the macrocyclic chelator DOTA with 52Mn in 0.1 M ammonium acetate, pH 4.5 at 37 °C was observed utilizing the natural Cr metal powder targets. The apparent molar activity was found to depend on the concentration of the eluant, especially for the natural chromium powder targets. When 52Mn was eluted with 0.1 M HCl, the apparent molar activity (AMA) was 185 ± 22.2 MBq/µmol (5.0 ± 0.6 mCi/μmol) and when 6 M HCl was used, the AMA increased to 999 ± 88.8 MBq/µmol (27.0 ± 2.4 mCi/μmol) as shown in Fig. 7.

Apparent molar activity of 52Mn as a function of the concentration of the elution solution.

The Cr target configurations presented explored additional techniques for the possibility of an enriched 52Cr target that would improve the production of 52Mn. The novel targets have challenges but could be improved upon with further investigation.

While some Cr foils are commercially available, Cr foils are very difficult to manipulate into discs since the material is brittle. The Cr metal powder was crafted into a pressed pellet for in the production of 52Mn. While this target configuration works well and could be consistently used for production of 52Mn it cannot be reused or recycled for a cost-effective means to utilize enriched 52Cr. 52Cr could be exchanged for natural Cr in this target configuration to prevent the production of 54Mn if the cost of the enriched material was not a factor. Ideally, the enriched material would be 100% recycled and the target could be reused multiple times which lead to exploration of additional Cr target configurations.

The Cr2O3 target does have the potential to be recycled since the final Cr species from the purification is CrCl3. The CrCl3 could potentially be reacted to make more Cr2O3 to make a new target. However, we were not able to dissolve this material which leads to purification issues. Finally, the electroplated Cr (III) target is the most promising since it has the potential to be recycled, can be dissolved/purified and it is less toxic than the well-known Cr(VI) electrodeposition. In order to improve the yield of Cr(III) on the Au surface new techniques need to be explored with the aim of yields greater than 90% at a thickness greater than 0.2 mm.

The concentration of the eluting solution affected greatly the AMA of the 52Mn produced. Higher concentrations of HCl acid selectively released 52Mn from the resin bed.

Enriched targets for the production of 52Mn should continue to be investigated in order to obtain a recyclable target that increase the yield and decreases the time of irradiation. Cr foil and Cr metal powder targets are routinely used for the production of 52Mn, however, these targets cannot be recycled in order to move to the enriched 52Cr target material. Cr2O3 is not feasible to use for natural or enriched targets because of the dissolution issues. Although the target is capable of giving higher yields when enriched material is used and it is possible to recycle through the CrCl3 to Cr2O3 reaction, it has been a challenge to dissolve and separate the 52Mn from the Cr. Finally, the Cr electroplated targets are the most promising for the future of enriched 52Cr targets for 52Mn production. These targets have the potential to be recycled by using the final CrCl3 in the new electroplating solution and the plated Cr can endure more current than the other targets described here leading to increased yields.

The datasets generated during and/or analyzed during the current study are available from the corresponding author on reasonable request.

Lewis, C. M. et al. 52Mn production for PET/MRI tracking of human stem cells expressing divalent metal transporter 1 (DMT1). Theranostics 5, 227–239. https://doi.org/10.7150/thno.10185 (2015).

Article CAS Google Scholar

Saar, G. et al. Anatomy, functionality, and neuronal connectivity with manganese radiotracers for positron emission tomography. Mol. Imag. Biol. 20, 562–574. https://doi.org/10.1007/s11307-018-1162-6 (2018).

Article CAS Google Scholar

Topping, G. J., Schaffer, P., Hoehr, C., Ruth, T. J. & Sossi, V. Manganese-52 positron emission tomography tracer characterization and initial results in phantoms and in vivo. Med. Phys. 40, 042502. https://doi.org/10.1118/1.4793756 (2013).

Article CAS Google Scholar

Graves, S. A. et al. Novel preparation methods of 52Mn for ImmunoPET imaging. Bioconjug. Chem. 26, 2118–2124. https://doi.org/10.1021/acs.bioconjchem.5b00414 (2015).

Article CAS Google Scholar

Fonslet, J., Tietze, S., Jensen, A. I., Graves, S. A. & Severin, G. W. Optimized procedures for manganese-52: Production, separation and radiolabeling. Appl. Radiat. Isot. 121, 38–43. https://doi.org/10.1016/j.apradiso.2016.11.021 (2017).

Article CAS Google Scholar

Bianchi, F. et al. On the production of 52gMn by deuteron irradiation on natural chromium and its radionuclidic purity. Appl. Radiat. Isot. 166, 109329. https://doi.org/10.1016/j.apradiso.2020.109329 (2020).

Article CAS Google Scholar

Brezovcsik, K., Veres, S., Molnár, J., Fenyvesi, A. & Szűcs, Z. Comparison of manganese uptake and transport of maize seedlings by mini-PET camera. Appl. Radiat. Isot. 160, 109127. https://doi.org/10.1016/j.apradiso.2020.109127 (2020).

Article CAS Google Scholar

Sciacca, G. et al. A universal cassette-based system for the dissolution of solid targets. Molecules https://doi.org/10.3390/molecules26206255 (2021).

Article Google Scholar

Barrett, K. E. et al. Radiochemical isolation method for the production of (52g)Mn from (nat)Cr for accelerator targets. Appl. Radiat. Isot. 146, 99–103. https://doi.org/10.1016/j.apradiso.2019.01.025 (2019).

Article CAS Google Scholar

El Sayed, R., Massicano, A. V. F., Queern, S. L., Loveless, C. S. & Lapi, S. E. Manganese-52 production cross-section measurements via irradiation of natural chromium targets up to 20 MeV. Appl. Radiat. Isot. 147, 165–170. https://doi.org/10.1016/j.apradiso.2019.02.017 (2019).

Article CAS Google Scholar

Wooten, A. L., Lewis, B. C. & Lapi, S. E. Cross-sections for (p, x) reactions on natural chromium for the production of (52,52m,54)Mn radioisotopes. Appl. Radiat. Isot. 96, 154–161. https://doi.org/10.1016/j.apradiso.2014.12.001 (2015).

Article CAS Google Scholar

NuDat 2.8. Brookhaven National Laboratory Website. https://www.nndc.bnl.gov/nudat2/. Accessed 24 May 2022.

Pyles, J. M. et al. Production of 52Mn using a semi-automated module. Appl. Radiat. Isot. 174, 109741. https://doi.org/10.1016/j.apradiso.2021.109741 (2021).

Article CAS Google Scholar

Liang, A., Ni, L., Liu, Q. & Zhang, J. Structure characterization and tribological properties of thick chromium coating electrodeposited from a Cr(III) electrolyte. Surf. Coat. Technol. 218, 23–29. https://doi.org/10.1016/j.surfcoat.2012.12.021 (2013).

Article CAS Google Scholar

Ziegler, J. F., Ziegler, M. & Biersack, J. P. SRIM: The stopping and range of ions in matter. Nucl. Instrum. Methods Phys. Res. B. 268, 1818–1823 (2010).

Article ADS CAS Google Scholar

Seo, M., Furuichi, R., Okamoto, G. & Sato, N. Dissolution of hydrous chromium oxide in acid solutions. Trans. Jpn Inst. Metals 16, 519–525. https://doi.org/10.2320/matertrans1960.16.519 (1975).

Article CAS Google Scholar

Zydorczak, B., May, P. M., Meyrick, D. P., Bátka, D. & Hefter, G. Dissolution of Cr2O3(s) and the behavior of chromium in concentrated NaOH solutions. Ind. Eng. Chem. Res. 51, 16537–16543. https://doi.org/10.1021/ie302096e (2012).

Article CAS Google Scholar

Download references

This project was supported by the Department of Energy Isotope Program under Grant DESC0015773 (PI: Lapi). The authors acknowledge the support of all team members from Dr. Lapi's group and UAB Cyclotron Facility.

Department of Radiology, University of Alabama at Birmingham, Birmingham, AL, USA

Jennifer M. Pyles, James M. Omweri & Suzanne E. Lapi

Department of Chemistry, University of Alabama at Birmingham, Birmingham, Al, USA

Jennifer M. Pyles, James M. Omweri & Suzanne E. Lapi

You can also search for this author in PubMed Google Scholar

You can also search for this author in PubMed Google Scholar

You can also search for this author in PubMed Google Scholar

J.M.P. conducted all experiments excluding the apparent molar activity, wrote the main manuscript and prepared Figs. 1, 2, 3, 4, 5, and 6 and all tables. J.M.O. conducted the apparent molar activity experiments, wrote the corresponding parts of the manuscript and prepared Fig. 7. S.E.L. provided concepts, feedback on experimental design and analysis, and supervision of this work and edited the manuscript.

Correspondence to Suzanne E. Lapi.

The authors declare no competing interests.

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.

Reprints and Permissions

Pyles, J.M., Omweri, J.M. & Lapi, S.E. Natural and enriched Cr target development for production of Manganese-52. Sci Rep 13, 1167 (2023). https://doi.org/10.1038/s41598-022-27257-w

Download citation

Received: 24 October 2022

Accepted: 28 December 2022

Published: 20 January 2023

DOI: https://doi.org/10.1038/s41598-022-27257-w

Anyone you share the following link with will be able to read this content:

Sorry, a shareable link is not currently available for this article.

Provided by the Springer Nature SharedIt content-sharing initiative

By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.